CANLEE
News information
CANLEE
News category
/
/
/
Metal laser cutting machine manufacturers: how to deal with abnormal reset of metal laser cutting machine

Metal laser cutting machine manufacturers: how to deal with abnormal reset of metal laser cutting machine

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-06-20 12:35
  • Views:

(Summary description)The laser cutting machine is to focus the laser light emitted from the laser into a high-power density laser beam through the optical path system. The laser beam shines on the surface of the workpiece to make the workpiece reach the melting point or boiling point, and the high-pressure gas coaxial with the beam blows away the molten or vaporized metal. Laser cutting machine is a commonly used processing equipment in modern times, and there will always be some headaches during use, especially its abnormal reset. This is also an issue that everyone is more concerned about. The following is a brief introduction to the abnormal reset of the metal laser cutting machine. How to solve the problem of abnormal reset of metal laser cutting machine?

Metal laser cutting machine manufacturers: how to deal with abnormal reset of metal laser cutting machine

(Summary description)The laser cutting machine is to focus the laser light emitted from the laser into a high-power density laser beam through the optical path system. The laser beam shines on the surface of the workpiece to make the workpiece reach the melting point or boiling point, and the high-pressure gas coaxial with the beam blows away the molten or vaporized metal. Laser cutting machine is a commonly used processing equipment in modern times, and there will always be some headaches during use, especially its abnormal reset. This is also an issue that everyone is more concerned about. The following is a brief introduction to the abnormal reset of the metal laser cutting machine. How to solve the problem of abnormal reset of metal laser cutting machine?

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-06-20 12:35
  • Views:
Information

The laser cutting machine is to focus the laser light emitted from the laser into a high-power density laser beam through the optical path system. The laser beam shines on the surface of the workpiece to make the workpiece reach the melting point or boiling point, and the high-pressure gas coaxial with the beam blows away the molten or vaporized metal. Laser cutting machine is a commonly used processing equipment in modern times, and there will always be some headaches during use, especially its abnormal reset. This is also an issue that everyone is more concerned about. The following is a brief introduction to the abnormal reset of the metal laser cutting machine. How to solve the problem of abnormal reset of metal laser cutting machine?

1. Check whether there is dust on the sensor, poor contact or damage (clean or replace the dust on the sensor);

2. Check whether the flexible conductive tape data cable of the metal laser cutting machine is in poor contact or damaged (trim the data cable and re-plug or replace the data cable);

3. Check whether the grounding wire is reliable or whether the high-voltage wire is damaged (re-ground or replace the high-voltage wire);

4. The motor wire is in poor contact.

The metal laser cutting machine has missing engraving, incorrect initialization, and the data has been sent (corrected); the operation sequence is reversed (re-enter); electrostatic interference (check whether the grounding wire is disconnected and restarted); computer system error (reinstall the operating system and software) ); Check whether the left and right belts are the same or whether the rear belt is too loose (belt is stretched); Check whether the belt or timing wheel is slipping or jumping (belt); Check whether the beam is parallel (re-adjust the left and right belts).

Keyword:

Scan the QR code to read on your phone

Relevant information

HOT NEWS

TOP
Product consultation
搜索
确认
取消
CANLEE

We are a large domestic group high-tech enterprise specializing in the R & D, manufacturing and sales of laser and complete sets of automatic welding and cutting equipment.

MENU

MESSAGE

Username used for comment:
首页留言
Description:

CONTACT US

+86-319-3977333

+86 15933391314

sales@canlee.com

No. 969,  Xingtai Street, Economic Development Zone, Xingtai City, Hebei Province, China

WeChat

WeChat

Copyright © 2021 Hebei Chuangli Electromechanical Technology Co., Ltd.